欧美69视频在线-欧美77777免费视频-欧美8888-欧美91av-欧美97欧美综合色伦图-欧美99

首頁 產品展示>強鹿柴油機活塞組件的拆卸技術方法與測量標準參數值

強鹿柴油機活塞組件的拆卸技術方法與測量標準參數值

我們是專業的強鹿柴油機活塞組件的拆卸技術方法供應服務商.我們可提供強鹿柴油機活塞組件的拆卸技術方法銷售維修保養零配件服務.強鹿柴油機活塞組件的拆卸技術方法想要更多的類型,請現在聯系湖南英珀威機械有限公司!
產品咨詢

詳細描述

強鹿柴油機活塞組件的拆卸技術方法

1. Remove piston rings using the JDE135 (shown),JDE85, or KJD10140 Piston Ring Expander.

2. Remove and discard piston pin snap rings.

3. Separate piston and rod. Keep these parts in placewith their respective cylinder liner.

John Deere約翰迪爾強鹿柴油機活塞環槽磨損的檢查與標準值參數

Pistons with tapered rods will use JDE62 Ring Groove Wear Gauge and pistons with straight rods will use JDG957 Ring Groove Wear Gauge.

1. Use the appropriate ring groove wear gauge (C) to check wear of keystone ring groove (top groove). Check grooves at several locations around the circumference of piston. Gauge shoulders should not contact ring land. Clearance (D) between shoulders of tool and ring land indicate ring groove is good. If ring groove is worn, replace piston and liner as a matched set. If ring groove is good, proceed to next step.

A—Piston with Good Keystone Ring Groove

B—Piston with Worn Keystone Ring Groove

C—Ring Groove Wear Gauge

D—Clearance (Normal)

E—No Clearance (Replace)

2. Check second (Compression) ring groove using new piston ring and a feeler gauge. Measure clearance at several points. Compare measurements with specifications.

3. Check third (Oil Control) ring groove using proper new piston ring and a feeler gauge. Measure clearance at several points. Compare measurements with specifications.

Specification

Piston Ring-to-Groove

Clearance—New Piston Ring

(Second Compression Ring

Groove)—Maximum Clearance.................................. 0.20 mm (0.008 in.)

Piston Ring-to-Groove

Clearance—New Piston Ring

(Third Oil Control Ring Groove,

Standard Ring)—Maximum

Clearance ................................................................... 0.82 mm (0.032 in.)

Piston Ring-to-Groove

Clearance—New Piston Ring

(Third Oil Control Ring Groove,

Heavy Duty Ring)—Maximum

Clearance ................................................................... 0.15 mm (0.006 in.)

4. Replace piston and liner (as a set) if clearance exceeds specification.

John Deere約翰迪爾強鹿柴油機活塞銷孔的測量與標準值參數

Measure piston pin bore. If bore is not within specification, replace piston and liner set.

Specification

Piston Pin Bore (Small Pin)—ID 34.935—34.945 mm (1.3754—1.3758 in.)

Piston Pin Bore (Large Pin)—ID 41.285—41.295 mm(1.6254—1.6258 in.)

活塞裙的測量與標準值參數

1. Measure piston skirt (A) 90° to piston pin bore and 28 mm (1.1 in.) from bottom of piston (B). Record measurement.

Specification

Piston Skirt (Measurement Taken at Bottom of Skirt 28 mm [1.1 in.]

from Bottom of Piston)—Diameter 106.38—106.40 mm (4.188—4.189 in.)

2. Measure cylinder liner as directed later in this groupand compare with piston measurement.

活塞的高度的測量與標準值參數

Measure piston height from center of piston pinbore-to-top of piston.

Piston (Two Valve Head Engines)—Specification

Piston—Height (Measured fromCenter of Pin Bore to Top ofPiston) 71.64—71.70 mm (2.820—2.823 in.)

Piston (Four Valve Head Engines)—Specification

Piston—Height (Measured fromCenter of Pin Bore to Top ofPiston) 71.60—71.65 mm(2.819—2.820 in.)

免費熱線
400-082-9096?
整機銷售
0731-84424871? 18374999699
售后維修
0731-84424872? 15580888444
配件銷售
0731-84424873? 18274802060
手機端
微信公眾號
主站蜘蛛池模板: 蜜桃日本一道无卡不码高清| 国产精品久久免费视频| 国产欧美日本在线观看| 99九九精品国产高清自在线 | 在线成人毛片| 亚洲视频免费在线看| 日日干夜夜操视频| 欧美特级大片| 久久久国产麻豆| 国产高h| 99精彩视频| 香蕉视频网站入口| 欧美三级做爰视频| 韩国19禁青草福利视频在线| 国产精品成人麻豆专区| 999毛片| 性生大片一级毛片免费观看| 日韩欧美三区| 久久精品国产久精国产80cm| 国产成人国产在线观看入口| 亚洲综合一| 天天操 夜夜操| 欧美中文在线观看| 久久天天躁狠狠躁夜夜爽| 狠狠色噜噜狠狠狠狠黑人| 国产凹凸在线一区二区色老头| 一区二区不卡| 天天操天天干天天做| 免费视频爱爱太爽了| 狠狠色狠狠色综合| 97se亚洲| 性欧美一级毛片欧美片| 欧美成人性色xxxx视频| 国产香蕉75在线播放| 99re66热这里只有精品首页| 五月天国产| 全部免费毛片| 久久久精品视频在线观看| 国产 麻豆 欧美亚洲综合久久| 综合一个色| 外国成人网在线观看免费视频|